Feed granulator other parts maintenance common sense

We in these parts of the feed pellet machine down time must be very careful, don't make a scratch in the surface of the parts, if accidentally scratched out for, working in this part will appear different ring, serious will stop work, in addition to remove when we should pay attention to these problems, we in the assembly when the poultry feed plant also want more attention, the first when we in the assembly of mechanical gears, we want to see the machinery crankshaft is very clean, if not clean.

We need to use a soft cloth or a new towel to get rid of the oil, together with the impurities, then from the new on the crankshaft, coated with a layer of oil, so that it can ensure the crankshaft rotating at did not produce any interference phenomenon, when there is a time when we are in the installation of the gear, we must watch the occlusal direction of gear, we must follow the direction of occlusion of the gear is installed, if we don't have in the direction of the occlusion of the gear to install, and may at the time of this cattle feed business machine rotation, the phenomenon of the gear fracture. When we install the gears, in addition to these directions to be clear, the more important thing is to look at the density of these gears, the density of these gears will change with the tightness of our screws. Only we carefully install our animal feed production will not be hurt!

Our company is a well-known poultry feed machine supplier, the company for many years has always adhered to the "to the customer's needs to produce, to customer's requirements as a service, and constantly to the development of science and technology, management and efficiency" business philosophy. For the general customer service, we sincerely hope that the company's products can improve your enterprise production efficiency, save costs, enhance the market competitiveness. At the same time, I hope you can put forward more valuable opinions and Suggestions in the process of using our products.

The role of the pressure roller in the pressure roller granulator

The correct use of the pressure roller is one of the most critical factors affecting the use of the cattle feed manufacturing business pellet machine. In our long-term production and service, we found that many ring dies have uneven working surface, low hole rate, reduced production capacity, and the new ring die poultry feed making machine  cannot produce material. Most of the reasons are Because of the irregular use of the pressure roller.

When using the ring die poultry feed plant, the characteristics of the new ring die are: the working surface is flat, but the smoothness in the eyeholes and the guide openings do not reach the smoothness required for normal granulation, and the eyelets of the new ring die have resistance to the material. And the friction is relatively large (especially the small aperture ring die), and the two ends of the old roll shell are more severely worn, and the material easily slips into the pressure relief groove from the wear on both ends of the roll shell, causing the new ring die to discharge Smooth or no discharge. Therefore, the new ring die must be equipped with a new roller shell. Ensure that it is used for more than 100 hours to ensure that the working surface of the new ring die is evenly compressed, and that the perforation rate and polishing rate meet the requirements. In order to give full play to the best performance of the ring die. In principle, each ring die must be equipped with a pair of pressure rollers when it is first used, and the same pair of roller shells cannot be used with other ring die strings.

The smallest small flour mill is a three - phase electric flour mill

ABC Machinery Small flour machine the smallest is three - phase electric flour machine! Small flour mill has been a demand for very large flour machine, many small household wheat milling process machine customer consulting domestic flour machine, two have a lot of customers is to 220 v electric flour mill, here to tell you: our ABC Machinery flour mill cost is three-phase electric flour mill, output the smallest flour machine is each hour 100 catties of automatic stone mill flour machine and semi-automatic stone mill flour machine, this kind of stone mill flour machine is grinding flour is does not destroy nutrients in wheat materials, keep stay green flour and very popular with today's pursuit of healthy people! Another kind of small flour mill is the steel mill flour machine, this kind of steel mill flour machine is divided into two models, one is the 40 model of 500-800 pounds per hour, the other is the 50 model of 800-1000 pounds per hour! So when you buy small flour machine can refer to the above provided content, strive to buy the most suitable for their own good and inexpensive flour machine!