Where will the rod making machine develop in the future

Since the introduction of the rod making machine, it has undoubtedly had a great impact on the entire market. However, due to various reasons, there are still big problems. So where will the sawdust briquettes making machine develop in the future?

1: Nowadays, most rod making machines still need manual operation. Perhaps with the development of technology, I believe that there will be fully automatic rod making machines without manual operation soon.
2: The output of rod making machine has improved. At present, the highest output of rod making machine rarely exceeds 10T/H. If matched with the production line, it can produce dozens of tons per hour at most. Many customers who require large output need to order several the set of rod making machines (units) can meet the demand for seats, but this answer greatly increases the floor space and invisibly increases a large part of the production cost. The breakthrough in output is the only way for the future development of the sawdust briquette maker.
3: The function of the stick making machine is diversified. Simply put, it is a machine with multiple functions. Although the stick making machine can also suppress crops such as straw and peanut shells at present, the sawdust, etc. still need to be pressed by a special sawdust stick making machine. In the future, there will be a real multifunctional stick making machine, which will integrate the pressing functions of feed, organic fertilizer and biomass pellets, and truly realize one machine with multiple functions.
4: With the improvement of the degree of particle forming, the rods pressed by the current rod making machines on the market often have cracks, uneven surfaces, etc., and in severe cases, powders may even be pressed. These are still unavoidable according to the current technical level. But it is believed that the forming aspect of the biomass briquettes machine will be greatly improved in the future.

ABC Machinery specializes in the production of sawdust rod making machines and biomass rod making machines. For more products login: www.bioenergy-machine.com.

How to Configure The Large Charcoal Machine Production Line

Some clients, after a survey, decide on a large charcoal machine. This automatic production line equipment must go to the regular factory, because there is no production plan of the factory will be one-sided will make your production line can not start production normally, spend a lot of money. So how to build a large sawdust briquettes machine production line?

Whether you are a small or large charcoal machine production line, there are several joint processes, one is the drying of biological materials, the second is the carbonization of raw materials. Therefore, in the whole charcoal production process, the integration of a reasonable dryer and carbonization furnace will be a powerful barrier to production. These all need to be built according to the actual situation. But the large charcoal machine production line all needs to construct the lumber mill, the raw material dryer, the charcoal powder molding machine and the carbonization furnace and so on.
The daily output of large charcoal machine equipment is as high as 10 tons or as high as dozens tons, which is important for large and medium-sized enterprises. Large charcoal machine equipment production, investment is also large, for large and medium-sized enterprises to bring high profits, deeply large and medium-sized enterprises porridge. Investment in large charcoal making machine investors should also consider the following points can be invested:

1. Plant: To invest in large sawdust briquette maker, first of all, to choose a large plant, ensure that it can be safe production.
2. Raw materials: Whether there is enough raw materials to enable normal production.
3. Capital: See if there is enough capital to keep the entire production line running.
4. Environmental trend: It is necessary to understand the environmental trend to see whether the carbon produced has a good environmental trend.
5. Workers: You need to find workers in advance, usually 8.

Pay attention to several aspects to make charcoal machines profitable

Currently, there are many manufacturers of charcoal making machine, each with different levels. There are many carbon plants all over the country. Some people who want to invest don't know much about it. How to make charcoal from sawdust? They want to know everywhere, but the effect is not very good. In order to operate a carbon plant, decision-makers first need to possess the following qualities:

1. Corporate business strategy decision-making capabilities and corporate management capabilities.
2, have the spirit of enduring hardship, perseverance, and not afraid of failure
3. The long-term supply of raw materials has a rich foundation, the cost of the products is indeed competitive, and the funds can be guaranteed and supported by many people.

　　
If all three are established, this is a good decision maker, and he will basically succeed. At the same time, there is no need to worry about the surplus of the product. At present, the domestic market is very large. Various industries demand charcoal. The insurance coefficient of running a charcoal factory is higher than that of any other enterprise. But at the same time need to pay attention to the following points:
1. The raw materials must be very cheap.
2, the choice of wood chip log making machine is better.
3. Good choice of technology, especially thruster repair technology and carbonized high temperature carbon technology.
　　
Pay attention to the above three conditions. While doing the maintenance work, you will basically get profit. Welcome new and old customers to buy.

Rear axle rod making machine

 

Brief introduction charcoal briquettes machine:

After the removal of shaft rod making machine is also known as the shaft after the charcoal machine, propeller design is unique, can be adjusted before and after the rod speed and density, whether it is shavings, bamboo or a variety of wooden chaff, propeller stirring can be automatically uniform blanking, equipped with 22 kilowatt motor, strong power yield is higher (when the production of 280-350 kg).

The performance characteristics of bagasse briquettes machine

ABC Machinery new high-speed rice husk briquette machine dismantling propeller repair, do not need to remove the molding cylinder and heater, the repair of the propeller directly from the middle of the belt pulley installation immediately boot direct production.

Remind: after disassembling after drawing, after adjusting, before disassembling these 3 kinds of models each have their merits, hope everybody chooses according to own demand.

Charcoal machine production of charcoal density, density, good flammability, can replace firewood and coal. This product is especially suitable for heating kang in autumn and winter in north China, heating greenhouses or making common life fuel.

9 common problems of charcoal rod making machine

 1. Transverse cracks on the rod. Excessive moisture in the raw material will easily cause transverse cracks on the rod.
2. Reasons for longitudinal cracks of the rod: a. The temperature is too high. b. The screw inclination is too large; c. The abrasive tool is damaged. Solutions for longitudinal cracks: a. Lower the temperature; b. Repair the inclination to be as perpendicular to the axis as possible; c. Replace or repair.
3. Reasons for too low rod density: a. The temperature is too high; b. The screw pressure is small. If the heating temperature is too high or too low, the forming sleeve is seriously worn, the propeller angle is not consistent, and the raw material has too much moisture. The solution to the density of the rod is too small: a. Cool down; b. Reduce the screw angle and increase the screw pressure.

4. The reason for the low density at the center of the rod or scattered sawdust: the diameter of the root of the propeller shaft tip needs to be repaired and thickened. Misalignment of the shaft tip can also cause the above problems, and it needs to be corrected at high temperature.
5. Back-gassing of the wood briquette machine: It is manifested in that gas is sprayed out from the discharge port during production, mainly due to insufficient material supply. It may also be due to excessive moisture in the raw materials and insufficient heating temperature.
6. The charcoal briquetting plant appears "stuffy": the raw materials are mixed with large and hard impurities. If the voltage is low or the heating temperature is too low, the raw material may not dry. The former needs to be shut down to remove impurities. The latter must continue to warm up to soften the raw materials, or re-dry.

7. Reasons for the charcoal briquette making machine to fire: a. The material is too moist; b. The stick is dead. Improper temperature control, excessive moisture in raw materials, abrasion of the propeller, improper shaft tip, clogged vents, too large or too small screw in the head of the propeller, serious sleeve wear, etc. In this case, compare the above reasons one by one, and make adjustments after finding out the reasons. The solution of the briquette machine for sale firing: a. Adjust the drying temperature and dry the material; b. See the solution to the dead eye of the stick.
 8. Reasons for bar bending: uneven heating and excessive moisture in raw materials. The solution to bar bending: increase the temperature.
 9. Reasons for the flower stick: a. The screw is not repaired; b. The mold is worn; c. The raw material is low in lignin. The solution of the flower stick: a. Reduce the screw thread angle and increase the screw pressure; b. Replace or repair; c. Mix the raw materials with heavier specific gravity, or replace the raw materials and wait for the raw materials to ferment for one to two months before using.

How is the production efficiency of the biomass briquette plant affected?

When the production line of the sawdust briquette press is working, because multiple machines are produced at the same time, the feeding and discharging are automatically completed by the conveyor, which greatly reduces the human resources. As long as each rod making machine can be stably produced, it should not pursue the maximum output of a single machine. Let the machine run at full load, because the sugarcane bagasse charcoal machine is more sensitive to the moisture content of the material and the crushing particle size requirements under full load. If there is a certain difference from the normal requirements, the discharge molding will be unstable, resulting in manual labor. The adjustment increases the labor intensity of the control personnel, and the production of other machines will also be affected to a certain extent! Therefore, the load of each host machine in the straw briquetting plant should be controlled within the rated load, to avoid the occurrence of unstable machine production caused by full load or overload operation, in order to improve the production efficiency of the entire biomass briquette plant.

The mechanism charcoal equipment has certain requirements on the raw material itself and the moisture content of the raw material. The raw material has a high lignin content, and the carbon content of the produced charcoal is high. In addition, the rod making machine generally requires that the moisture of the raw material is between 5% and 12%. If the moisture is high, it needs to be dried first.

Machine charcoal equipment generally uses sawdust or rice husks as raw materials, neither of which needs to be crushed. Secondly, wood shavings, bamboo shavings, branches, wooden scraps, fruit shells, etc. are also good raw materials, but they need to be crushed first, and the requirements for the crusher are also relatively high.