Feed granulator other parts maintenance common sense

We in these parts of the feed pellet machine down time must be very careful, don't make a scratch in the surface of the parts, if accidentally scratched out for, working in this part will appear different ring, serious will stop work, in addition to remove when we should pay attention to these problems, we in the assembly when the poultry feed plant also want more attention, the first when we in the assembly of mechanical gears, we want to see the machinery crankshaft is very clean, if not clean.

We need to use a soft cloth or a new towel to get rid of the oil, together with the impurities, then from the new on the crankshaft, coated with a layer of oil, so that it can ensure the crankshaft rotating at did not produce any interference phenomenon, when there is a time when we are in the installation of the gear, we must watch the occlusal direction of gear, we must follow the direction of occlusion of the gear is installed, if we don't have in the direction of the occlusion of the gear to install, and may at the time of this cattle feed business machine rotation, the phenomenon of the gear fracture. When we install the gears, in addition to these directions to be clear, the more important thing is to look at the density of these gears, the density of these gears will change with the tightness of our screws. Only we carefully install our animal feed production will not be hurt!

Our company is a well-known poultry feed machine supplier, the company for many years has always adhered to the "to the customer's needs to produce, to customer's requirements as a service, and constantly to the development of science and technology, management and efficiency" business philosophy. For the general customer service, we sincerely hope that the company's products can improve your enterprise production efficiency, save costs, enhance the market competitiveness. At the same time, I hope you can put forward more valuable opinions and Suggestions in the process of using our products.

The role of the pressure roller in the pressure roller granulator

The correct use of the pressure roller is one of the most critical factors affecting the use of the cattle feed manufacturing business pellet machine. In our long-term production and service, we found that many ring dies have uneven working surface, low hole rate, reduced production capacity, and the new ring die poultry feed making machine  cannot produce material. Most of the reasons are Because of the irregular use of the pressure roller.

When using the ring die poultry feed plant, the characteristics of the new ring die are: the working surface is flat, but the smoothness in the eyeholes and the guide openings do not reach the smoothness required for normal granulation, and the eyelets of the new ring die have resistance to the material. And the friction is relatively large (especially the small aperture ring die), and the two ends of the old roll shell are more severely worn, and the material easily slips into the pressure relief groove from the wear on both ends of the roll shell, causing the new ring die to discharge Smooth or no discharge. Therefore, the new ring die must be equipped with a new roller shell. Ensure that it is used for more than 100 hours to ensure that the working surface of the new ring die is evenly compressed, and that the perforation rate and polishing rate meet the requirements. In order to give full play to the best performance of the ring die. In principle, each ring die must be equipped with a pair of pressure rollers when it is first used, and the same pair of roller shells cannot be used with other ring die strings.

The smallest small flour mill is a three - phase electric flour mill

ABC Machinery Small flour machine the smallest is three - phase electric flour machine! Small flour mill has been a demand for very large flour machine, many small household wheat milling process machine customer consulting domestic flour machine, two have a lot of customers is to 220 v electric flour mill, here to tell you: our ABC Machinery flour mill cost is three-phase electric flour mill, output the smallest flour machine is each hour 100 catties of automatic stone mill flour machine and semi-automatic stone mill flour machine, this kind of stone mill flour machine is grinding flour is does not destroy nutrients in wheat materials, keep stay green flour and very popular with today's pursuit of healthy people! Another kind of small flour mill is the steel mill flour machine, this kind of steel mill flour machine is divided into two models, one is the 40 model of 500-800 pounds per hour, the other is the 50 model of 800-1000 pounds per hour! So when you buy small flour machine can refer to the above provided content, strive to buy the most suitable for their own good and inexpensive flour machine!

 

ABC Machinery to teach you how to open an oil mill steps and proceeds

If you want to open an oil mill business, how much output of oil mill equipment do you need? Because, if you need large equipment, then buy a complete set of mustard oil plant, so you need to communicate with the manufacturer, find professional engineers to solve your problems, with professional matching equipment.
There are mainly four machines in the oil press workshop, one is the sheller, the other is the seed frying machine (wok), the third is the oil press and the fourth is the oil filter. But one and two are optional equipment, three and four are necessary equipment, of course, can also be combined into a machine, that is the combined machine (press rate all-in-one machine).Open an oil mill, need to do what preparation?

First, study the market, understand the market conditions, so that more reasonable sales products.
Second, understand each manufacturer's soybean oil machine model and quality, ABC Machinery machine quality and credibility are guaranteed, welcome customers to come to consult and order.

Third, the estimated cost, the general medium coconut oil processing machine, the cost of about 20,000, the general supporting facilities have wok and feeding machine, these are customers can match can not match the equipment, see customer needs!
Fourth, estimate the location and size of the facade. Geographical location is chosen in farmer's market or fair commonly, appearance is left and right sides 20 square metre commonly.

Fifth, the approval of relevant documents and three-phase electricity.
Sixth, there will be some problems or problems at the beginning, please feel free to call us at any time ABC Machinery mill, we are happy to help you solve.
Seventh, basically on the right track, customers can rest assured production, processing and sales, later can also consider increasing the scale.

Daily inspection of corn processing equipment

 

Every day must do the inspection work to the corn flour milling process equipment! Any mechanical equipment in the daily operation should pay attention to the equipment repair and maintenance work, daily detection is very important for the machine, maize processing equipment is not exceptional also, daily to detect before operation, not only can avoid the happening of some malfunction but also can prolong the service life of mechanical, as much as possible so as to ensure that our corn flour mill plant, production time, to strive for more economic benefits! So be sure to do daily check!

Specific testing of corn processing equipment:

1. Inspection of its key facilities.

2. Testing the status of maize milling process machinery.

3. Conduct subjective state monitoring when the corn processing machinery is shut down.

4. Regularly carry out large-scale testing and maintenance, that is, regularly replace parts of corn deep-processing machinery or carry out repairs.

5. Check the transmission parts, safety protection parts, supporting points and power connection parts of mechanical equipment to ensure the normal operation of mechanical equipment.

 

Secondly, in the process of use, it is necessary to timely clean up the corn processing equipment and sundries at the operation site to prevent the safety hidden dangers caused by flour mill project machinery and sundries at the site. In order to strengthen the on-site preventive work, if necessary, protective barriers or safety warning signs should be installed around the work site to prohibit non-working personnel from entering the work site. The work site should be unobblocked and equipped with necessary protective equipment and facilities. It is necessary to do a good job in daily testing, so as to avoid a series of mechanical failures in the operation process of the equipment, so as to improve its production efficiency, but also to ensure the personal safety of operators!

What is the reason for the uneven output of the feed pellet machine?

The feed pellet machine is currently the most widely used livestock feed manufacturing machine. Because the products it manufactures are easy to store, transport and feed, it is loved by the majority of farmers. However, the feed pellet machine sometimes occurs during use, such as the pellets containing more powder, the size of the pellets produced is not uniform, and the pelleting machinery does not discharge these common problems. Farmers or feed processing plants should understand some simple failure causes in the daily use of machinery, and be able to take corresponding measures to remedy them in time.

1. There is a problem with the blade and gear of the poultry feed production machine. The formation of feed pellets mainly relies on the rotation of the pellet machine gear to drive the blades to cut pellets. Once the gears or blades are eliminated, the size of the cut feed particles will be uneven.

2. There is a problem with the motor. The motor equipped with the poultry feed making machine is a motor that is compatible with its rated power. Once it is damaged in the working process or the working power is unstable, it will not be able to pelletize or the pelleting will be uneven.

3. Operational problems. Irregular operation of operators will also cause uneven pellets in cattle feed manufacturing plant. For example, the granulation powder contains a large amount of water, which prevents the feed pellets from being formed, or they are easy to crack when exposed to cold wind after forming. If this situation is encountered, the operator should calmly analyze, find out the cause, and make timely remedies. So as not to affect the pelleting output and cause corresponding economic losses.

How to solve the abnormal situation of the noodle machine

 In the wheat processing plant, we cannot do without the use of the beating machine, which is prone to some small problems in the long-term work. At this time, we need to have a new understanding of the failure of the beating machine. We can identify where the fault occurs at the first time, and what is the reason for the failure? How should we solve this problem? These problems are familiar with, so that we can face in the emergence of problems can be the first time to solve, to ensure the production time and efficiency of the face machine! ABC Machinery professional manufacturer of flour to talk about flour milling process machine abnormal conditions should be solved?

 

If there is an abnormal condition in the operation of the noodle machine, the power must be cut off first, and the fault can only be checked after the power is cut off, which is also a safety measure for maintenance personnel. If the machine does not operate after being powered on, the possible fault is: the power supply contact is bad or the plug is loose; Bad contact of power switch; Poor contact of microswitch; The thermal protector is out of order. Troubleshooting measures are: replace the connector or repair the power supply, check whether the switch is damaged, adjust the micro switch, replace the heat protector. After the motor does not turn, it will also produce vibration or slow speed. The fault situation is: the mechanical part is stuck; The centrifuge is not on. Too low voltage can also cause this situation, the way to remove the trouble is to clean up the foreign matter in the crushing tank, after starting the machine, idle for half a minute, then slowly feed and adjust the power supply voltage.

Correct understanding of all kinds of abnormalities, is the face machine users friends should pay attention to the problem! I hope you can use the maize flour machine in the process of smooth!

 

Cold pressing and hot pressing of screw oil press

Now customers will ask whether our crops need to be fried or not? In fact, it is the difference between cold pressing and hot pressing of crops. Some crops can be steamed and fried, some crops do not need to be fried, depending on the situation! The following is the difference between cold pressing and hot pressing:
The so-called hot pressing means that the peanuts are fried in a wok and then pressed with an small scale oil mill. Cold pressing means that the peanuts are pressed directly without being fried!

Hot pressing is to squeeze the seeds of oil crops after roasting, with special fragrance, darker color and higher yield. There is less residue in the product and it is easy to store. The cold-pressed seeds are not roasted, so the smell is poor, but the color is good. Cold pressing does not need to heat the oil, the oil yield is low, the crude oil is light in color, has less impurities, and can retain more nutrients in the oil. It is suitable for some small varieties of oils or high-grade health oils that are not suitable for heating. Hot pressing requires heating oil (steaming and frying), and the oil yield is high, which is currently a common method. Therefore, hot pressing and cold pressing do not matter whether it is good or bad, it just depends on the needs of customers, but some crops must be hot pressed, such as sesame and tea seeds; some crops must be cold pressed, such as oil sunflower (also melon seeds). Generally, it is hot pressed once and cold pressed twice. This way the oil output rate is relatively high! The specific need for hot pressing or cold pressing depends on the oil crops to be pressed and the habits of customers.
After deciding how to squeeze, you can select the corresponding type of peanut oil processing equipment.

ABC Machinery is a professional oil equipment manufacturer, providing oil presses, complete production lines, oil mill project, palm oil processing plant and other kinds of grease equipment.

Rear axle rod making machine

 

Brief introduction charcoal briquettes machine:

After the removal of shaft rod making machine is also known as the shaft after the charcoal machine, propeller design is unique, can be adjusted before and after the rod speed and density, whether it is shavings, bamboo or a variety of wooden chaff, propeller stirring can be automatically uniform blanking, equipped with 22 kilowatt motor, strong power yield is higher (when the production of 280-350 kg).

The performance characteristics of bagasse briquettes machine

ABC Machinery new high-speed rice husk briquette machine dismantling propeller repair, do not need to remove the molding cylinder and heater, the repair of the propeller directly from the middle of the belt pulley installation immediately boot direct production.

Remind: after disassembling after drawing, after adjusting, before disassembling these 3 kinds of models each have their merits, hope everybody chooses according to own demand.

Charcoal machine production of charcoal density, density, good flammability, can replace firewood and coal. This product is especially suitable for heating kang in autumn and winter in north China, heating greenhouses or making common life fuel.

9 common problems of charcoal rod making machine

 1. Transverse cracks on the rod. Excessive moisture in the raw material will easily cause transverse cracks on the rod.
2. Reasons for longitudinal cracks of the rod: a. The temperature is too high. b. The screw inclination is too large; c. The abrasive tool is damaged. Solutions for longitudinal cracks: a. Lower the temperature; b. Repair the inclination to be as perpendicular to the axis as possible; c. Replace or repair.
3. Reasons for too low rod density: a. The temperature is too high; b. The screw pressure is small. If the heating temperature is too high or too low, the forming sleeve is seriously worn, the propeller angle is not consistent, and the raw material has too much moisture. The solution to the density of the rod is too small: a. Cool down; b. Reduce the screw angle and increase the screw pressure.

4. The reason for the low density at the center of the rod or scattered sawdust: the diameter of the root of the propeller shaft tip needs to be repaired and thickened. Misalignment of the shaft tip can also cause the above problems, and it needs to be corrected at high temperature.
5. Back-gassing of the wood briquette machine: It is manifested in that gas is sprayed out from the discharge port during production, mainly due to insufficient material supply. It may also be due to excessive moisture in the raw materials and insufficient heating temperature.
6. The charcoal briquetting plant appears "stuffy": the raw materials are mixed with large and hard impurities. If the voltage is low or the heating temperature is too low, the raw material may not dry. The former needs to be shut down to remove impurities. The latter must continue to warm up to soften the raw materials, or re-dry.

7. Reasons for the charcoal briquette making machine to fire: a. The material is too moist; b. The stick is dead. Improper temperature control, excessive moisture in raw materials, abrasion of the propeller, improper shaft tip, clogged vents, too large or too small screw in the head of the propeller, serious sleeve wear, etc. In this case, compare the above reasons one by one, and make adjustments after finding out the reasons. The solution of the briquette machine for sale firing: a. Adjust the drying temperature and dry the material; b. See the solution to the dead eye of the stick.
 8. Reasons for bar bending: uneven heating and excessive moisture in raw materials. The solution to bar bending: increase the temperature.
 9. Reasons for the flower stick: a. The screw is not repaired; b. The mold is worn; c. The raw material is low in lignin. The solution of the flower stick: a. Reduce the screw thread angle and increase the screw pressure; b. Replace or repair; c. Mix the raw materials with heavier specific gravity, or replace the raw materials and wait for the raw materials to ferment for one to two months before using.

Sawdust granulator complete production line

 

ABC Machinery can provide a full set of wood pellet plant and production equipment, including the screening of raw materials, transport, grinding, drying, mixing, granulation, cooling, dust removal, packaging and other links, easy to operate, stable performance, easy maintenance. The whole line has a high degree of automation, the feeding amount of raw materials does not need manual control, pulverizer, dryer, gemco pellet mill and so on adopt frequency modulation feeding, the finished product is automatically weighed. The production line adopts imported noise reduction equipment and pulse dust removal system with noise volume less than 80 dB and dust degree less than 50mg/m3.

First of all, the production of pto driven pellet mill depends on what kind of raw materials are in your hand. If you take sawdust and shavings as raw materials, the size must be able to pass through the screen hole of about 8mm-12mm. If the branches and some waste boards in your hand must have been crushed or even need to be sliced to improve the production capacity. We require 10% to 16% water, and no more than 2 to 4% water. If the water is too much, we will need to equip you with drying equipment. If the water is too small, it is necessary to mix wood chips with relatively high water content in proportion to appropriate water content.

To sum up, the configuration of sawdust production line can be divided into slicing section, drying moisture pretreatment section, mixing buffer section, particle section, packaging section and the supporting electrical control system, dust treatment system, transport system, temperature control system and other major projects. In the granulator main machine, we use the circular mold granulator, called circular mold granulator, which is composed of vertical circular mold and internal drum, pressure on the circular mold (circular mold).The material in the delivery system enters the center of the particle chamber through a vane propeller. In the pellet chamber, the drum (press roller and spindle) is stationary, and the die (ring die) is moving, similar to the washing machine. The raw material is first passed through a rotating mold and then extruded by a roller. Circular mould sawdust particle machine will not appear the cylinder is not uniform, and because the distance between inside and outside is equal, will not appear wear. It is more suitable for mass production. For one thing, the loss value of roller and mold is relatively low. Second, it is more energy efficient. Due to the extra friction caused by the roller sliding, the flat mold granulator needs to consume more energy. However, the additional friction does not have only negative effects, because friction generates heat, which is beneficial for particle production. But too much heat reduces productivity, so we increase the temperature control system to keep the temperature in the particle room constant. ABC Machinery sales of wood pelletizer, biomass granule machine accessories such as sawdust granule machine.

How to choose a cost-effective peanut sheller

 ABC Machinery is a manufacturer specializing in the production of soybean oil mill and its supporting equipment. As we all know, the peanut peeler is also an inseparable part of peanut oil. When customers purchase cooking oil machine, some will need to be equipped with a peanut peeler; In order to prevent customers from encountering scams when purchasing a peanut sheller separately, today I will tell you what functions a good peanut sheller should have, so that customers can use it as a reference when purchasing. Deceived.

The peanut shelling machine is a machine that removes the peanut shells and keeps the peanuts intact through a high-speed rotating body.
1. The hulling is clean and the productivity is high. For hulling machines with cleaning devices, higher cleanliness is also required.
2. Low loss rate and small broken rate. ③Simple structure, reliable use, convenient adjustment, low power consumption, certain versatility, can remove a variety of crops to improve the utilization rate of machinery.
2. Requirements for peanuts (skin fruit). Peanuts are suitable for dryness and wetness. If they are too dry, the breakage rate will be high, and if they are too wet, work efficiency will be affected. The peanuts (skins) stored in rural areas are generally dry. The following methods can be used to make them dry and wet.
3. Shelling in winter. Before shelling, spray about 10 kg of warm water on 50 kg of rind and cover with plastic film for about 10 hours, and then dry it in the sun for about 1 hour to start shelling. Use in other seasons. The plastic film covering time is about 6 hours, and the rest is the same.
4. Dried peanuts (skins) can be immersed in a large pool, immediately removed after soaking and covered with plastic film for about 1 day, and then dried in the sun, and begin to shell after drying and wet.

5. Requirements for voltage and choice of workplace. For a single-phase motor to work normally, the voltage must reach its rated voltage. In rural areas, there is generally only one transformer in a village, and households are scattered, and the wires and circuits used are not very standard, resulting in insufficient voltage for users far away from the transformer. Therefore, the workplace should choose a place closer to the transformer. ABC Machinery provides various grease equipment, such as: mustard oil extraction process machine, palm oil processing plant cost, vegetable oil making machine, etc.

How is the production efficiency of the biomass briquette plant affected?

When the production line of the sawdust briquette press is working, because multiple machines are produced at the same time, the feeding and discharging are automatically completed by the conveyor, which greatly reduces the human resources. As long as each rod making machine can be stably produced, it should not pursue the maximum output of a single machine. Let the machine run at full load, because the sugarcane bagasse charcoal machine is more sensitive to the moisture content of the material and the crushing particle size requirements under full load. If there is a certain difference from the normal requirements, the discharge molding will be unstable, resulting in manual labor. The adjustment increases the labor intensity of the control personnel, and the production of other machines will also be affected to a certain extent! Therefore, the load of each host machine in the straw briquetting plant should be controlled within the rated load, to avoid the occurrence of unstable machine production caused by full load or overload operation, in order to improve the production efficiency of the entire biomass briquette plant.

The mechanism charcoal equipment has certain requirements on the raw material itself and the moisture content of the raw material. The raw material has a high lignin content, and the carbon content of the produced charcoal is high. In addition, the rod making machine generally requires that the moisture of the raw material is between 5% and 12%. If the moisture is high, it needs to be dried first.

Machine charcoal equipment generally uses sawdust or rice husks as raw materials, neither of which needs to be crushed. Secondly, wood shavings, bamboo shavings, branches, wooden scraps, fruit shells, etc. are also good raw materials, but they need to be crushed first, and the requirements for the crusher are also relatively high.

Factors affecting the service life of straw pellet machine

ABC Machinery is mainly engaged in high-quality straw pellet machine, wood pellet plant and other equipment(rotary drum dryer, pellet packing machine). The wood pellet making machine is made of crop straw or sawdust as raw materials, and is pressed into cylindrical pellets by the straw pellet machine.

Factors affecting the life of gemco pellet mill
1. The moisture of the material is too low, the hardness of the processed object is high, and the power consumption during processing is large, which increases the production cost of the enterprise and reduces the service life of the straw pellet machine. If the moisture is too large, it is not easy to crush and increases the impact of the hammer The number of times, at the same time, heat is generated due to the friction of the material and the impact of the hammer, which evaporates the internal moisture of the processing object, the evaporated moisture and the crushed fine powder form a paste and block the sieve, which reduces the discharge of the crusher. The moisture of grains, corn, etc. is controlled below 14%.

2. A permanent magnet cylinder or iron remover can be installed at the feed inlet of the machine, so as not to affect the service life of the pressure wheel, mold and central shaft. The temperature of the straw particles during the extrusion process is as high as 50-85°C, and the pressure wheel is running it is under strong driving force during work, but lacks the necessary and effective dust protection device, so the bearings must be cleaned every 2-5 working days, and high temperature grease must be added. The main shaft of the commercial wood pellet mill every other month after cleaning and refueling, the gear box should be cleaned and maintained at intervals of half a year, and the screw tightening and replacement of the transmission part should be carried out at any time.

3. When the material pressing is about to end, mix a little wheat hull with edible oil and put it into the machine. After 1-2 minutes of pressing, the machine is shut down to fill the mold hole with oil so that it can be put into production next time. It also saves man-hours. After the straw pellet machine stops, loosen the pressure wheel adjustment screw and remove the residual material.

The above three factors are the main factors affecting the service life of the straw pellet machine. On the other hand, the use of straw pellet machine is gradually expanding.

The difference between small sawdust granulator and feed granulator

Small sawdust particles machine is a lot of use in more than a decade ago, at that time the main is to use a new type of animal feed mill, because at that time many do feed manufacturers need to feed and then crushed granules, on the one hand, convenient to store, on the other hand feed particles are small and convenient, is advantageous to the animal digestion and absorption, is very popular with breeding users. So at that time the feed pellet machine is very popular, the sale is very popular and thus spawned a large number of feed pellet machine manufacturers.

In recent years, with the promotion of low-carbon and environmental protection in China, more and more places have begun to give up traditional coal as the raw material for combustion, and use sawdust or straw particles as the raw material for new energy. The demand for sawdust particles is most prominent in large power plants. On current trends, supply still outstrips supply. Under this environment, the sale of small sawdust granulator also once popular, in order to have better income, there are many traditional pellet feed mill manufacturers, give up the basic line of responsibility, feed granulator sold to the user to suppress sawdust particles. However, sawdust particles are much lighter than feed particles, more difficult to press than feed particles, so the traditional poultry feed production process machine is very difficult to suppress sawdust particles, and because of the market needs of the pressure, high wear, the service life of the machine is also very short.

We also remind everyone here, when buying chicken feed production machine, must be clear about small sawdust granulator, or feed granulator. Avoid losing money. Choose Anyang GEMCO sawdust granulator, sawdust granulator, sawdust crusher is not wrong, both energy saving and environmental protection, our company guarantees the quality of production, will provide you with the most satisfactory service!

Increasing demand for biomass briquette plant has become inevitable

Nowadays, environmental problems have become more and more a topic of concern to society, and the greenhouse effect has become more and more serious. As a substitute for coal-fired materials, biomass briquette plant have been widely used at home and abroad. Our company has successfully developed its own environmentally friendly and energy-saving wood chip rod making machine through this environmentally friendly product. Friends from all walks of life are welcome to visit purchase.

Sawdust rod making machines and rice husk charcoal making machine are mainly aimed at waste wood chips and straws, and these two types of materials are also the most produced in China, and are most urgently needed to be treated, construction waste, domestic waste, furniture industry every moment A large amount of waste wood will be generated. If these waste wood are directly discarded, it will not only cause pollution to the environment, but also greatly waste renewable resources. There are also straws, which produce a lot of straws in autumn every year. In the past, the people directly burned the straws, which not only wastes resources, but also greatly pollutes the environment. The disposal of crop straws has also been a concern of the country and local governments. In this case, a machine capable of processing wood chips and straws and turning them into valuables is particularly important, and the importance of wood shavings briquette maker and straw making machines at this time is revealed.

Demand for sawdust rod making machines increases: As the price of grain increases, the discarded crops, sawdust and straw can be reprocessed using sawdust rod making machines and straw rod making machines, and the pellets can be sent directly Go to power plants, replace coal, and use as new energy. This greatly reduces costs and is recognized by more and more customers.

Best Roller Sawdust Particle Machine

Sawdust straw pellet machine is suitable for pressing hard-to-bond and shaped materials, such as branches, trunks, bark and other wood scraps; used in fuel plants, wood processing plants, fertilizer plants, chemical plants, feed plants, etc., it is a farmer. The most compact compression molding equipment with small investment, quick results and no risk.

Benefits of Best sawdust pellet mill:
1. Best gemco pellet mill does not need to add water or dry during the granulation process. After natural heating up to about 70 ℃, the internal ripening is deep, the surface is smooth, the hardness is high, the particle size is adjustable, and the pellet feed is processed. All kinds of additives can be added in the medium, the nutrition loss is very small, and it can kill pathogenic microorganisms and parasites, and ensure the quality of feed.
2. The best palatability of the pellet machine feed pellets gelatinize the starch in the mixed powder during the pressing process, so that the compressed feed pellets have a certain flavor, increase the palatability of the feed pellets, can stimulate The appetite of livestock and poultry makes them prefer to eat, and the protein is organized to enhance the enzyme activity, so that the beans and grains contained in the feed hinder the digestion and utilization of nutrients (such as anti-trypsin factor), these Both improve the digestibility of feed. It has been determined that feed pellets can increase feed intake by 10% -15%. Sterilize and reduce disease. During the compression process of feed pellets, a short period of high temperature as high as 70 ℃ -100 ℃ can kill part of parasite eggs and pathogenic microorganisms, so that the disease of rabbits is significantly reduced. Practice has proved that the diarrhea, stomatitis and anorexia of poultry and livestock fed with pellets are significantly reduced.

​​​​​​​GEMCO animal feed mill

GEMCO energy machinery factory is a professional manufacturer of animal feed mill. Since our company was founded in 2007, we have advanced technology and more than 9 years of manufacturing experience. We are committed to the research and development and production of small pellet feed machine, so as to provide more convenient and better services for the majority of breeding users.

GEMCO energy machinery manufacturer specializes in the production of small feed granulator, small scale feed mill is corn, soybean meal, straw, grass, rice husk and other crushing directly pressed particles of feed processing machinery. Feed pellet machine is widely used in large, medium and small aquaculture, grain feed processing plants, livestock farms, poultry farms, individual farmers and small and medium farms, farmers or large, medium and small feed processing plants.

USES of feed granulator produced by GEMCO small granulator manufacturer: poultry feed production process machine, small household granulator, small poultry granulator, fish feed granulator, rabbit feed granulator, pig feed granulator, straw feed granulator; According to the production can be divided into: straw granule machine, wheat bran feed granule machine, soybean meal feed granule machine, corn straw feed granule machine, sawdust straw granule machine. A variety of different feed pelletizing machines differ in appearance and mode of production from that of classification.

Is Oil Press Pressed Grade Higher Better

Recently a client called to ask you if ABC Machinery had a 5.6-stage press.

In this regard, today we ABC Machinery plant home of the technical chief worker to give you a simple share of the current domestic market screw oil extractor suitable for the pressing grade! There are three stage screw press and four stage screw press, three stage screw press technology is the most mature, suitable for raw press and hot press, four stage press series relative to the three stage press, is not so mature, the main defect is that the raw press when the amount of slag is large, and hot press effect is very good. There are a lot of screw small oil mill brands on the network now, claiming that their oil press is five grade press, six grade press, and most consumers think that the higher the series of press, the higher the oil yield will be. This is a misunderstanding, is not correct, we should correctly understand the squeeze series and the oil rate of the relationship, not to be fooled by those unscrupulous businessmen.

The factors that determine the oil yield of the screw press are temperature and pressure. If the temperature of the screw press is not controlled accurately, the oil yield will be affected. If the pressure is not up to the standard, even the ten-stage press is useless. The temperature value is the temperature in the chamber when the screw oil press is working. Different oil crops have different optimal pressing temperature, which is determined by the characteristics of mustard oil business. The squeezing force refers to the friction pressure between the extruder head of the screw and the extruder bar, which is not increased by adding several extruder heads, but by increasing the pressure of each extruder head. When consumers buy screw oil extractor, should avoid this misunderstanding, do not be misled and fooled by advertising.

Specific how to choose the oil press, cooking oil refinery can go to our website to understand with more information, or directly contact us.

Small Oil Mill Plant Introduction

With rich market knowledge as well as experience, we have been able to emerge as a trusted manufacturer and supplier of oil mill plant. We could customize the groundnut oil processing plant according to your raw material and desired handling capacity. The edible oil production line can process more than 20 kinds of oilseeds such as peanut, soybean, sunflower seed, palm kernel, copra, rapeseed, castor seed, flax seed, cottonseed, corn germ, sesame, walnut, pine nut, argan nut, mustard seed, moringa seed, camellia seed, jatropha seed, etc. The capacity of the edible corn oil production plant is up to 100 tons per day. We could send two engineers for on-site installation, commissioning and training.

Main Machines in Edible Oil Production Line
1.Oilseed Shelling Machine  
Some oilseeds have shells which have to be removed before pressing. Our peanut shelling machine can shell the peanuts by rubbing force, separate the shells and kernels by wind force and then separate the unshelled peanuts by gravity separating screen. The unshelled peanuts are shelled again. The shelling rate of the peanut shelling machine is higher than 95% and the crushing rate is lower than 5%.

2. Oilseed Cleaning Machine
The cleaning sieve can remove stone, dust, defective seeds and other impurities in the oilseeds. The aim of oilseeds cleaning in small oil mill plant is to improve the quality of oil and cake, increase the oil yield, increase the handling capacity and protect the equipment.

3. Oilseed Roasting Machine  
Rotary roaster machine is used in the edible oil plant for heating the oilseeds which could increase the oil yield. The roasting machine can be heated by coal, gas or firewood, having a large heating area, uniform heating effect, and fast roasting speed, greatly increasing the service life of the roaster and improving the roasting quality.

4. Oil Press Machine 
Automatic screw oil press can press the oil out of the oilseeds and then filter the crude oil. The machine consists of an automatic control system, pressing part, transmission system, adjusting part and vacuum filtering device. It features high oil yield and pure oil.
If you choose to use screw oil press in the oil processing plant, the frame oil filter is suggested for crude oil filtration. The filter press can bear large pressure and is safe to use. It is also suitable for filtering the bleached oil.

5. Edible Oil Refinery
Edible oil refinery plant can turn crude oil obtained from the oil press machine into the refined oil with good color and high quality. The plant includes a degumming process, neutralizing process, bleaching process, and deodorizing process. The refining process can remove phospholipids, free fatty acids, pigments, odor substances and other impurities in the crude oil. (palm kernel oil refining process>>)

6. Edible Oil Filling Machine
Refined oil can be filled into bottles by edible oil filling machine. There are automatic and semi-automatic edible oil quantitative filling machines. Adopts double speed filling, first fast and then slow, ensuring the filling speed and preventing overflow.

We can also provide special oilseed processing equipment, such as how to make prickly pear seed oil?

Cold Pressing Hydraulic Oil Press Advantages

Cold Pressing Hydraulic Oil Press Machine for Sales

Hydraulic oil press machine is now the most cost effective and environment-friendly equipment for oil extracting. It is durable, efficient and easy to operators. More importantly, it can achieve the cold pressing. Therefore, more and more people tend to choose hydraulic oil press machine to start their oil mill business.

Oilseeds Can be Processed by Hydraulic Oil Press

Compare to traditional oil press machine, hydraulic oil press machine can process much more oilseeds, including coconut, sesame seeds, sunflower seeds, groundnut, cashew nut, almond, walnut, soybeans, etc.

Advantages of Hydraulic Oil Press Machine

• High oil output, high efficiency and easy operation
• Both hot pressing and cold pressing available
• Various oil seeds are suitable for hydraulic oil press machine
• Stainless steel body ensure sanitation and long-term use
• Pure physical pressing and consistent temperature ensure high quality oil

Groundnut Oil Machine & Groundnut Oil Extraction Process

Groundnut/Peanut Oil Introduction

Groundnut/Peanut Oil is yellow and transparent. It has little fragrance tastes delicious. It is an edible oil that can be digested easily. Groundnut/Peanut oil contains more than 80% unsaturated fatty acids (including 41.2% oleic acid and 37.6% linoleic acid). It also contains fatty acids such as palmitic acid, stearic acid and arachidic acid. The fatty acid composition of groundnut/peanut oil is better and easy to be digested and absorbed by human body.

Therefore, groundnut/peanut oil is popular with consumers. But, how to extract groundnut/peanut oil? ABC Machinery can offer Business Plan for Groundnut Oil Production for small scale or large scale oil factory.

Groundnut Oil Machine Types

With the development of edible oil processing industry, there are various groundnut oil extraction machine for home use or commercial use. The most popular groundnut oil extraction machine are screw oil press, integrated oil press, and hydraulic oil press machine.

Small Grounndut Oil Machine

Groundnut/Peanut Oil Extraction Process

Before entering the peanut oil extraction machine, the peanut kernels should be pretreated. Peanut pretreatment includes cleaning, husking, crushing, steaming and frying processes.

• Cleaning: The peanut being transported to groundnut oil processing plant usually contains certain impurities (silt, gravel, iron filings, etc.). If these impurities aren't removed or selected out carefully, the oil extraction machine would be damaged, lower oil output and even cause faults and accidents. Cleaning peanuts before peanut oi press machine is beneficial to reduce oil loss and improve oil yield of peanut oil press, improve the quality of oil, cake and by-products and increase the processing capacity of peanut oil press equipment;
• Shelling: Peanuts should be shelled and then pressed to increase production capacity and peanut oil yield. Its supporting equipment is: sheller, separation screen, separator and so on.
• Crushing: The yield of peanut can be increased obviously by crushing, rolling and pressing. Its supporting equipment is: crusher, rolling machine, etc.
• Steaming and Frying: Steam frying is an important step to improve the oil yield, the commonly used method is to wet the oil first, and then dry the wok, so that the oil to meet the technical requirements of water and temperature.
• Oil Extraction: The pretreated peanuts can be pressed by peanut oil processing machine. The commonly used peanut oil press is screw oil press machine that can be used to process more than 30 kinds of oil crops such as peanut, rapeseed, oil sunflower, cottonseed, soybean, flaxseed, and more. 
• Oil Filtering: Filtering is to remove the organic impurities contained in crude grounanut oil. The supporting equipment is plate and frame oil filter machine. 
• Oil Refining: This process is designed to produce high quality edible cooking oil and prelong the storage period. 

ABC Machinery Website:
https://www.abcmach.com
http://www.bestoilpressmachines.com